※海外からのお取り寄せ商品の為、お届けまでに通常約2-3週間を頂戴しております。※税関にて開封される場合がありますが、新品・未使用商品です。※並行輸入品のためパッケージに輸送時に伴うスレや傷がある場合がございますが、商品に問題はございませんので予めご了承くださいませ。
・This item is made in 514-Moss Green 80/20 Loop carpet. The item image may be a different color, but the SWATCH image is the correct color. Carpet Fits Low Tunnel. Unless otherwise noted, the jute padding is heat bonded to the backside of the carpet and a heel pad is welded to the correct location.
・Holes may not be cut in automotive carpet and carpet may require trimming to install. PLEASE FIND THE INSTALL INSTRUCTIONS ON THE HELP TAB IN OUR STORE DETAILS PAGE.
・Automotive carpet compatible with Chevrolet Standard Cab Pickup Truck will be Heat and Pressure formed using a form that was created from the original floor pan. Carpet is guaranteed to fit to the floor when installed correctly.
・All automotive carpets are Made in USA with Top Quality auto carpet materials. IF YOU ARE NOT 100% SURE OF THE COLOR/MATERIAL YOU NEED, PLEASE CONTACT US BEFORE ORDERING.
・Automotive carpet will fit just like original carpet when installed correctly and is Guaranteed against Defects. This item fits the years: 1955 1956 1957 1958 1959
説明:
This automotive carpet will be made in 514-Moss Green 80/20 Loop.
Other colors and materials may be available in the selection above.
This carpet is a replacement for 1955 to 1959 Chevy Standard Cab Pickup Truck, Low Tunnel. This carpet is flat in the tunnel area, it does not have a molded hump in the tunnel area. Front end of carpet extends approximately 6 inches above steering column.
Carpet will be made with standard flexibe polyethylene backing. Contact us to upgrade to massbacking
Unless specified, the jute padding will be attached in the foot area of the carpet
Installation may require trimming around the edges and the holes may need to be cut.
There is a large variety of colors available. Please request free samples if you want to match a specific color
This item fits the years: 1955, 1956, 1957, 1958, 1959, 55, 56, 57, 58, 59
READ FULL INSTRUCTIONS BEFORE BEGINNING - Instructions may vary for multi-piece sets
1. Remove new product from box. Lay flat and pop contours back into place. Allow a few hours for product to relax back into proper shape. Check material for accuracy
2. Compare new and old carpet
3. Use old carpet as a template for console cuts
4. IMPORTANT: Fold new product in half from front to rear. Place in vehicle lining up molded contour to seat risers or any other identifiable starting point. Once fitted, continue installation
5. Roll product forward make cuts for brackets, shifters vents etc while maintaining proper alignment on seat risers or other starting point
6. Cut in center at firewall to allow product to go underneath dash
7. Continue for remainder of installation, working to outer edges
8. Once carpet is properly fitted, do the final trim on outer edges, seat belts, holes, etc
Note: If adhesive is desired, only apply a light brush or spray adhesive after correct dry fit has been obtained.
カテゴリー: 車両用マット
メーカー: ACC
ブランド: ACC
高さ: 27.9 センチ
幅: 101.6 センチ
奥行: 27.9 センチ
重量: 7.3 Kg
※海外からのお取り寄せ商品の為、お届けまでに通常約2-3週間を頂戴しております。※税関にて開封される場合がありますが、新品・未使用商品です。※並行輸入品のためパッケージに輸送時に伴うスレや傷がある場合がございますが、商品に問題はございませんので予めご了承くださいませ。